Curtis 1314 pc programming station software download

CURTIS 1314 PC PROGRAMMING STATION SOFTWARE DOWNLOAD HOW TO
CURTIS 1314 PC PROGRAMMING STATION SOFTWARE DOWNLOAD FULL
CURTIS 1314 PC PROGRAMMING STATION SOFTWARE DOWNLOAD SERIES

for about $275 less $60 core charge upon return of your old controller. ItвЂ™s a question of removing the entire motor controller and replacing it as one unit. The purpose of this test bench is to test controllers and firmware as they get released on the market. We typically use a rubber insulated socket available at the hardware store. The controller will power up via the USB cable so no external power supplies are needed.

CURTIS 1314 PC PROGRAMMING STATION SOFTWARE DOWNLOAD SERIES

5 and a Non-DCS Series Motor System from 1994. Curtis 1206 test - Buggies Gone Wild controllers in Figure 2, and for the 1209M and 1221M controllers in Figure 3. How do I test my ezgo TXT controller?Put F/R lever in Forward and connect the Black test lead to the B- terminal on the controller and connect the red test lead to the M- terminal on the controller. Test Procedure 5, -14 3) Failed solenoid diode. The Alltrax controller is a part on your cart that works with your throttle sensor to manage electrical flow. For testing we need it to be in USER control, so if your LED is not GREEN then we need to change modes. E-Z-Go gas cart Starter/Generator and Voltage Regulator When the solenoid is energized through the logic switches (Key Switch and Accelerator Switch), current flows from B+ through the solenoid, to F2 of the Starter/Generator, though the field winding to F1, through the strap, to A2, through the armature to A1 to ground.

CURTIS 1314 PC PROGRAMMING STATION SOFTWARE DOWNLOAD FULL

If you have checked the battery and found it to be charging properly and providing a full amount of power to The problem can often be solved by just tightening down the loose part to the controller board. LED blinks 6 times red on controller power up.

About the I was wanting to test the controller again now that it is off the cart was my reason for asking about a bench test. The 600 Regen offers even more torque and is for heaver loads like larger tires and towing. com/how-do-i-test-my-ezgo-txt-controller View Now AllВ .

CURTIS 1314 PC PROGRAMMING STATION SOFTWARE DOWNLOAD HOW TO

Thoughts on how to properly bench test one of these. Now we have to test in-put voltages to the controller. To test your Tow-Pro Elite brake controller, connect a 21W globe between the earth pin (3) and trailer brake pin (5) of your trailer base. Notice that the yellow wire from the computer is connected to the foot pedal switch and to the controller. Step Two: Attach the 10-gauge jumper wire from F1 to A2. Some voltages are dictated by what the voltage of the car is. Connect B+ and M- to the two wires to the lamp. It's very complete, I used it to wire my cart from scratch, using a Curtis 1205 controller. Why to Unit Test View Controllers and Views. Background Information Test bench waveforms, which you have been using to simulate each of the modules Figure 3. Description: Curtis 36 volt 350 amp PDS (1206MX-4301) regen solid state speed controller. Mount relay on top of Alltrax controller using the stock bolts to secure the relay to the plastic inserts. controller key switch ignition interlock charger socket solenoid traction motor wht wht blk blk grn/blk grn/blk e-z-go (dcs) wiring diagram red red red/wht red/yel orn/red yel red orn grn yel blu red red/yel red yel/wht test 4 run rev 36 volts press acc pedal. Step Three: Attach the negative ( BLACK) battery cable to the negative terminal on the battery. This will allow you to correct the problem with your EZ GO goft cart electric motor. C1236 E text ThunderStruck Curtis 1244 Controller Bench Test 1314 Software. The actual reading may not be exactly what the potentiometer is rated for. This can potentially damage some controllers. the solenoid is clicking when I depress the pedal and I think that I have narrowed it down to the controller or the induction throttle controller. thanks for your help the cart is a series model no switch the solenoid clicks when the pedal is pushed i get a 37.

My Ju2 -301340 Yamaha Electric golf cart 48v.

Test Procedure 4, -13 Solenoid 1) Loose wires. I just want a way to test it outside the car without having to uninstall / reinstall each of them. ANY solenoid it can be tested in several different ways. To conduct the light bulb test, you can use a single light bulb or lamp. The motor is a key component to any EZ-Go electric golf cart. I tested it while on the cart (per EzGo's tech manual) and it shows bad.

Curtis 1314 pc programming station software download